GIANTS Software - Forum

Hello everyone,
Wanna to show with you some fresh screenshots.
There is a new options:
-New unattached position (gooseneck goes in upper position)
-Adjust semitrailer attacher and deck heights to allow you to use that trailer without problem, for example, on rough terrain with special lifted trucks or with lowered showtrucks.
-Optional ramps to get ability to use space above wheels (not so realistic, but useful).
-Extendable wide expander.
-STZ-VP 2 version
-North American version.
-Planned to add tension belts (when model changes will be finished).

Ok, so little update:
-Added extendable wide expander -Added STZ-VP 2 version

Great job!


Is it possible to put the optional red / white signals?

In North America, it's a orange triangle mostly.

Best Regards,

Tekkev

Tekkev wrote: ↑Thu Mar 26, 2020 1:51 pm Is it possible to put the optional red / white signals?

In North America, it's a orange triangle mostly.

Thanks. Can you show photos for example?

Actually, NA trailers will have red and white conspicuity tape around the edges, as close to eye level as possible

Bryan83 wrote: ↑Thu Mar 26, 2020 6:30 pm Actually, NA trailers will have red and white conspicuity tape around the edges, as close to eye level as possible

Yeap, got you. Will try to do something

macenkodenis94 wrote: ↑Thu Mar 26, 2020 6:45 pmYeap, got you. Will try to do something

The white goes forward on the sides, then on the back the red is on the outer side.

I don't think you can do it on consoles because of scripts, but maybe a bonus for PC/MAC players is that the tape is reflective IRL.

Edit: There isn't any on the front of trailers.

Bryan83 wrote: ↑Thu Mar 26, 2020 7:28 pm

	The white goes forward on the sides, then on the back the red is on the outer side. I don't think you can do it on consoles because of scripts, but maybe a bonus for PC/MAC players is that the tape is reflective IRL. Edit: There isn't any on the front of trailers.

Something like that?

Yeah, that's good. Maybe add a strip or 2 to the back down where the bumper would be, and then for a NA version we don't have the signs that are up on the deck.

Personal note, dang that was fast. You're good.

Bryan83 wrote: ↑Thu Mar 26, 2020 7:37 pm Yeah, that's good. Maybe add a strip or 2 to the back down where the bumper would be, and then for a NA version we don't have the signs that are up on the deck.

Can you show some img of bumper stipes?

Bryan83 wrote: ↑Thu Mar 26, 2020 7:37 pm Personal note, dang that was fast. You're good.

I just reuse stock textures, so that's not hard. And one quastion. Is there a combined stoplight in US, or i need to use round lights instead?

macenkodenis94 wrote: ↑Thu Mar 26, 2020 7:34 pm

Bryan83 wrote: ↑Thu Mar 26, 2020 7:28 pm

	The white goes forward on the sides, then on the back the red is on the outer side. I don't think you can do it on consoles because of scripts, but maybe a bonus for PC/MAC players is that the tape is reflective IRL. Edit: There isn't any on the front of trailers.

Something like that?

The circled signs are what I'd remove and then placement notes for the strips on the back

Bryan83 wrote: ↑Thu Mar 26, 2020 7:43 pm The circled signs are what I'd remove and then placement notes for the strips on the back

And a stripe on rear bumper, can you show example?



P.S.: When you quote with images, please put it under spoiler.

macenkodenis94 wrote: ↑Thu Mar 26, 2020 7:59 pm

	And a stripe on rear bumper, can you show example? P.S.: When you quote with images, please put it under spoiler.

So that's a freight trailer setup, but a low loader in NA would have the same round lights all 4 come on as tail lights then the 2 inside lights are the brake lights and the 2 outside are the turn signals

Bryan83 wrote: ↑Thu Mar 26, 2020 8:39 pm

So that's a freight trailer setup, but a low loader in NA would have the same round lights all 4 come on as tail lights then the 2 inside lights are the brake lights and the 2 outside are the turn signals

In stock assets there is no tail light+turn light round NA style lights. Only tail light+brake light and turn light separately.
Now there is something like this:



Gooseneck decals will be reworked tomorrow.
How about double bumper white-red line? Is that right? Or i need to remove top line?
Is red-white lines must to be equal in size of red and white? Or red must to be longer, than white?
Did i need to add red and white flickers to red-white lines?

One or 2 lines is a matter of preference, and I think it looks good how you have it, but if you decide to take one row off, take the top one and leave the one on the bottom. As far as sizing, you can either do equal lengths red and white, or you can do about 2/3 red and 1/3 white, I've seen both. If you want to add flicker to simulate reflectivity, that might be a nice touch, but I'd like to see how that would look.

macenkodenis94 wrote: ↑Thu Mar 26, 2020 10:09 pm

	Bryan83 wrote: ↑Thu Mar 26, 2020 8:39 pm So that's a freight trailer setup, but a low loader in NA would have the same round lights all 4 come on as tail lights then the 2 inside lights are the brake lights and the 2 outside are the turn signals

In stock assets there is no tail light+turn light round NA style lights. Only tail light+brake light and turn light separately.
Now there is something like this:



Gooseneck decals will be reworked tomorrow.
How about double bumper white-red line? Is that right? Or i need to remove top line?
Is red-white lines must to be equal in size of red and white? Or red must to be longer, than white?
Did i need to add red and white flickers to red-white lines?